banner



Home  ›  Where To Get Rear View Camera Installed

Where To Get Rear View Camera Installed

Written By Wednesday, June 15, 2022 Add Comment Edit

Download Article

Download Commodity

A rear-view camera, as well known as a backup photographic camera, lets you lot encounter what's backside your vehicle without having to look backwards. Though the device comes standard with many new car models, you can add a rear-view camera to your vehicle if it didn't come with ane.

  1. 1

    Buy a mountable backup photographic camera for your specific vehicle. For safe, make sure you purchase a device specifically designed to be a rear-view camera. Purchasing one fabricated for your specific vehicle will make it easier to install than a standard aftermarket photographic camera. So y'all tin install information technology easily, expect for a camera that mounts onto or directly behind your license plate.[1]

    • Look for fill-in cameras at consumer electronics stores.

  2. 2

    Get an external monitor if you want to go on your existing rear-view mirror. An external backup monitor is a small video screen that mounts onto your windshield similarly to a GPS. Though they take up more than space than internal monitors, external monitors are far easier to see and can be hands replaced if necessary.

    • If you lot'd like, y'all can employ a standard video monitor instead. However, keep in mind that information technology may not take all the same features as devices designed for use with backup cameras.

    Advertizement

  3. 3

    Buy an internal monitor for a less obtrusive device. An internal backup monitor is a fully functioning rear-view mirror that houses a small screen within the glass. Some internal monitors clip on height of your electric current rear-view mirror, merely others supervene upon your original mirror entirely.[2]

    • Most internal monitors shut off and disappear when not in use, making them a perfect choice if yous desire to preserve your car's looks.

  4. 4

    Buy ability and video cords if your camera and monitor didn't include them. For most rear-view photographic camera installations, you'll need camera and monitor splitter cords with connectors for video and power cables, 2 bare wire power cables, and an RCA video cable.[3]

    • Most installation kits include these cables, but some may require you to purchase them separately.
    • Some photographic camera models apply wireless transmitters instead of standard video cables.

    5. Advertisement

  1. i

    Take off your rear license plate. Using a Phillips head screwdriver, remove each of the screws holding your rear license plate in place. Then, pull the plate off and set it aside.[4]

    • Make certain y'all identify the screws in a safety identify and then you lot don't lose them.

  2. 2

    Remove your torso's interior panel. Pop open your trunk and look for a solid interior panel covering the opposite side of your license plate mounting area. So, insert a trim removal tool or other sparse device behind the panel and pry it off.[v]

    • Removing this panel will expose the auto's rear wiring chambers.

  3. 3

    Drill a small hole in the license plate mounting area. Make certain there are no obstructions between the license plate mountain and the rear wiring chamber. Then, create a small pigsty in the machine using a power drill equipped with a high-speed twist drill fleck. Line up your hole so it is straight behind where your camera's power and video cable volition go.[6]

    • To effigy out where to make the hole, hold your camera up to the area you intend to mountain it. And then, notation the spot where its splitting cord sits.
    • Create a hole that's large enough to fit your camera's ability and video cable.
    • If you come across any obstructions, endeavour to remove them. If yous can't, see if you can make a pigsty nearby.
    • For most jobs, you'll need a drill bit that has a diameter between i⁄8 and one⁄iv  in (0.32 and 0.64 cm).

  4. 4

    Place a prophylactic grommet effectually your photographic camera cable. Before running your photographic camera cablevision into the car, skid a rubber grommet onto it near the non-splitting end. These small rubber washers, bachelor at virtually habitation improvement stores, will keep the wire in place and foreclose leaks.[7]

    • Choose a grommet that'south only large enough to fit inside the drilled hole.

  5. 5

    Run the camera cable into your trunk. Pull the splitting end of your camera's video and power cablevision through the drilled hole into the body of your car. Make sure you pull it tight then the rubber grommet lodges into the drilled pigsty.

    • Your photographic camera cable should run from the outside of the car to the inside of the car.

  6. half dozen

    Locate your motorcar'due south 2 contrary light wires. Reverse calorie-free wires are the cords that connect your machine's tail lights to the dashboard. They hook straight into your vehicle's tail lights and are normally located in the hatch or trunk of your car.

    • These cords look dissimilar for every vehicle so, if you can't detect them, consult your owner's manual for model specific information.

  7. vii

    Strip and divide your automobile'due south reverse light wires. Using a wire stripper or pliers, pare back the safety covering the wires. So, utilise a screwdriver or other thin tool to poke a pigsty through the heart of each exposed wire, separating the individual wire strands.[8]

    • For safety, brand sure y'all do this while the car is turned off.

  8. 8

    Fuse your camera wires with the reverse light wires. Attach 1 of your bare wire cables to the camera cord's power connector. So, poke your bare wires through the centre of the exposed contrary light wires and twist them together. For safety, make certain you lot wrap the combined wires in electrical tape.[9]

    • Make sure you poke your positive (usually scarlet) bare wire through the positive contrary light wire and the negative (usually blackness) bare wire through the negative reverse low-cal wire.

    9. Advertisement

  1. 1

    Route your camera's video cablevision to the front of the auto. Connect your RCA cablevision to the camera cord's video connector if necessary. Then, run it through your vehicle to the area past the fuse box. Depending on your vehicle model, you lot'll usually be able to practise this past peeling dorsum the auto's headliner or side panels and pulling your cable through the exposed sleeping accommodation.[10]

    • For certain trucks, you may demand to run the video cable through the vehicle's frame rails.
    • In near cars, you'll find the fuse box underneath the steering wheel.

  2. 2

    Fix external monitors to the front windshield. If you lot're installing an external monitor, commencement adhere your device's included mount to the windshield by following the manufacturer's included instructions. Then, hook your monitor onto the mount.

    • Well-nigh external monitors use a suction mount, though others may come up with a more than complex mounting system.

  3. 3

    Adhere internal monitors to the rear-view mirror or mirror mount. For certain internal monitors, you'll need to clip the new device onto your electric current rear-view mirror. For others, y'all'll need to take off the mirror and slide your monitor into the pre-existing mirror mount.[xi]

    • Some internal monitors may come with their own mounting organization that yous'll take to attach to the car's forepart windshield.

  4. 4

    Run the monitor'southward splitter cable to the fuse box. If necessary, hook your monitor's ability and video cablevision into the device. So, route the cablevision from the monitor to the area next to the fuse box.[12]

    • If you'd like, use a trim removal tool to pop out the headlining panel directly higher up your windshield. Then, run your cable through the exposed bedroom.

  5. 5

    Connect your monitor's camera cable to the RCA cable. Afterward routing your monitor's splitter cable, connect the video end of the cable to your camera'southward RCA cord. Then, wrap the connected cords with electrical record to hold them together.

    • If your RCA and video cables have the same ends, you may need to purchase an RCA male person to female converter cord. Yous tin find these at most electronic stores.

  6. half-dozen

    Attach your monitor'southward power cablevision to a fuse tap. Connect your remaining bare wire cable to the backup monitor's power cord. Then, push button the positive (ordinarily red) stop of the bare wire cable into the open up end of a fuse tap. Finally, crimp the ii cables together with a pair of pliers.[13]

    • A fuse tap is a minor cable that converts a bare wire into a fuse signal. You can find them at virtually auto role stores.
    • If you'd prefer, you lot can leave the bare wire cable off and connect your camera'southward power cable to a cigarette lighter adaptor. Then, plug this adaptor into your car's cigarette lighter receptacle for power.

  7. 7

    Plug the fuse tap into the fuse box. Locate your fuse box and open it upwards. Then, plug your fuse tap into an open fuse prison cell. If necessary, check your fuse box'due south chapeau or your vehicle'due south education manual to see which slots are open.[14]

    • After attaching your fuse, consider taping all your wires together using electrical tape to get them out of the style.

    8. Advertising

  1. 1

    Connect your backup photographic camera to its power and video cable. Return to the dorsum of your car one time you've installed the rear-view monitor and all the necessary photographic camera cords. Close the trunk if necessary, then connect the backup photographic camera to its power and video cable.

    • Your camera's power and video cable should be sticking out of the pigsty yous drilled in the license plate mounting area.

  2. two

    Mountain the camera to your license plate. If the camera attaches to the forepart of your license plate, fix it to the plate by following the manufacturer's included instructions. If the camera attaches to the dorsum of your license plate, line the device up with the plate'southward fastener holes and thread screws through them.[xv]

    • In almost cases, you tin attach a rear-view camera to the back of your license plate using the screws y'all removed from the auto earlier.

  3. 3

    Reattach your license plate and trim panels. Using a Phillips head screwdriver, put your rear license plate back on your vehicle. Once you've reattached it, requite the license plate and backup photographic camera house tugs to make certain they're secure.

    • If yous haven't already, reattach your car's interior trunk panel and other trim panels past pressing them back onto the vehicle.

  4. 4

    Examination the photographic camera to make sure everything works. Before using your new camera on public roads, test it in a rubber expanse similar your driveway. If it turns on, identify a big, durable object like a trash can behind the photographic camera to see how distorted the paradigm is. If it does not plough on, read your installation manual for troubleshooting data.

    • In many cases, rear-view camera malfunctions are caused by loose or improperly continued wires.

    5. Advert

Add together New Question

  • Question

    I hooked the photographic camera upward and it just flickers. Any advice?

    Community Answer

    You lot may want to ensure all cables and connections are secured tightly. Double check that all connections are correct. If this doesn't piece of work, check to see if the camera called is in good shape and isn't physically damaged.

  • Question

    Suzuki installed reverse parking camera in my Swift Dzire Zxi. Only the camera shows upper view and non the footing below. What tin I do ?

    Community Answer

    Make sure that the camera is installed the right style (not upside down), and check the position of the camera mounted. Take it dorsum to the dealer that installed it and ask them to bank check the alignment and fit.

  • Question

    What is the best peak for a reversing camera?

    Cashj2

    There is no optimal elevation for a back-up camera. The ideal top is based off the specific car or vehicle that you have and your personal preferences, along with its intended application. Some back-up cameras are placed on large service trucks so that they tin line up to trailer hitches easier, some are to forestall a blindspot on the road. Depending on your awarding, it tin can be placed at any height. Almost reversing cameras are a "wide view" style and the specific tiptop location does not e'er touch the style it functions.

  • Question

    So if I hooked upwardly all the wires correctly but nevertheless no power, is it a fuse tap that I need to splice into the wires for information technology to work correctly?

    Shannon Phillips

    Shannon Phillips

    Customs Respond

    Cheque your earth or footing information technology may be bad. Utilise your multimeter to encounter if the ground is okay.

  • Question

    Is it still okay to connect the back-up camera to the opposite low-cal with cars that have car lighting? Or, would I need to connect to the reverse wire on the gearbox?

    Shannon Phillips

    Shannon Phillips

    Community Answer

    Yes, that will be fine, that how information technology is supposed to be washed. Await for an auto electrician if you lot need someone to call.

Ask a Question

200 characters left

Include your electronic mail address to become a message when this question is answered.

Submit

Advertising

  • Though near car dealers and mechanics will not install aftermarket fill-in camera systems, many audio and electronic shops will.

Advertisement

  • Make sure you lot turn the car off before working with bare or stripped wires. If you demand to touch exposed wires while the machine is on, put on a pair of shock-resistant rubber gloves.

Advertisement

Things You'll Need

  • Rear-view camera
  • Rear-view monitor
  • Connector cables
  • Phillips head screwdriver
  • Trim removal tool
  • Power drill with high-speed twist scrap
  • Condom grommet
  • Wire stripper or pliers
  • Electrical record
  • Fuse tap

Almost This Commodity

Commodity Summary X

To successfully install a rear-view camera, first remove your vehicle'southward rear license plate and interior trunk panel. Using a ability drill, punch a small hole through the exposed license plate mounting expanse and run your camera's power and video cord through it. Attach a bare wire power cable to your camera'southward ability connector, so strip your motorcar's reverse light wires and splice them with your bare wire power cable. To acquire how to mount the rear-view camera and fill-in monitor, scroll downwards!

Did this summary help yous?

Thanks to all authors for creating a page that has been read 262,862 times.

Did this article help you?

Source: https://www.wikihow.com/Install-a-Rear-View-Camera

Posted by: biermannoccowell.blogspot.com

0 Response to "Where To Get Rear View Camera Installed"

Post a Comment

Subscribe to: Post Comments (Atom)

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel